Note：This product will be EOL soon, please consider the Grove - OLED Display 1.12'' V2 as alternative choice.
Grove - OLED 1.12'' is a 16 color grayscale 96×96 dot matrix OLED display module with Grove compatible 4pin I2C interface.Grove - OLED 1.12" is constructed with 96 x 96 dot matrix OLED module ([ LY120])and SSD1327 driver IC. The characteristics of this display module are high brightness, self-emission, high contrast ratio, slim / thin outline, wide viewing angle, wide temperature range, and low power consumption.
Dot Matrix: 96 x 96 Pixels
Color: Grayscale Display (16 Gray shades)
Supports both Normal and Inverse Color Display
Supports Continuous Horizontal Scrolling
Grove compatible 4pin I2C connector
Works with both 5V and 3.3V logic MCUs
Wide range of operating temperature: -40 °C ~ 70 °C
Graphic display adapter for Seeeduino and Arduino using Grove stem board
Display adapter for any 5V or 3.3V MCU which supports I2C interface
Can be used with mbed microcontroller
|Dimensions||40mm x40mm x10mm|
|Grove - OLED Display 1.12''||1|
Flying BeagleBone Green
BBBmini is a state of the art Linux autopilot / flightcontroller Cape for the BeagleBone. It can be used for Copter, Planes or Rovers.
Automated Plant Watering System
A device that waters plants and monitors temprature using an ESP8266 and Android app.
IoT in Conventional Agriculture!
Our mission with nature is to preserve it, designing and implementing technologies and monitoring methods with the help of IoT via Helium.
Grove - OLED Display 1.12"
Wiki of Grove - OLED Display 1.12"
Love these little displays. Can't beat them for under $15.00
Easy to use Facile
The files are ok, can be downloaded and included, but something is wrong. I cannot run the examples on my "Romeo ALL in one controller"
I hope to be able to run the module.
Thank you!Question by: admin on 2018-12-18 02:38:56
Dear customer, the libraries is not support Arduino 1.0 yet.So suggest you use Arduino 0023 to compile those codes.And could be work. :)Answer by: admin on 2018-12-18 02:38:56
It's for the 'Grove - OLED 96x96'.
I'm not able to download the 'Seeed Gray OLED library' zip file, it's always corrupted. Could you see that it work, please?
GuyQuestion by: admin on 2018-12-18 02:38:56
Hello, I measured 230V with the switchable x1/x10 probes in x10 mode. I didn't notice anything wrong.Answer by: admin on 2018-12-18 02:38:56
When trying to download schematics for this module from wiki, I get nothing. The link I am trying to use is: http://www.seeedstudio.com/wik...Question by: admin on 2018-12-18 02:38:55
thanks for your suggestion. acutlly, the designer has tried to do this, but for some reason, it is not stable. we will give his your suggestion .Answer by: admin on 2018-12-18 02:38:55
With the 1.12" OLED Display it is possible to print Float Numbers using the command SeeedOled.putFloat(), but in this screen the only command available is .putNumber()!
How do I print float type numbers in this display?!Question by: admin on 2018-12-18 02:38:55
I can put floats using this :
SeeedGrayOled.putString(tmp);Answer by: admin on 2018-12-18 02:38:55
The method SeeedGrayOled.clearDisplay() do nothing on my code.
I write on the screen but when i call clearDisplay nothing happens.
I'm using UNO R3.
Thanks!Question by: admin on 2018-12-18 02:38:55
This function should be used before starting a fresh start or after scroll deactivation,such as SeeedGrayOled.init();Answer by: admin on 2018-12-18 02:38:55
Can it show images in 16 shades of gray? Already use this one, see text in shades in sample code, but no such code for images.Question by: admin on 2018-12-18 02:38:55
You can set level of gray via this command : SeeedGrayOled.setGrayLevel(i); // the minimum value is 0,the maximum value is 15.Answer by: admin on 2018-12-18 02:38:55
I'm using Seeedino Stalker v2.2 and Grove - Base shield. I connected this OLED into the first I2C slot. It was looking OK just before pulsing my G1/2 Water Flow Sensor with digital pin 2 (interrupt 0). So I changed the pin of G1/2 Water Flow sensor froQuestion by: admin on 2018-12-18 02:38:55
Hi,i have tested its program,and it's ok.OLED and Water Sensor can be uesd together.Please check your program again ,and you can sent a e-mail to us if you have any question detailedly.Answer by: admin on 2018-12-18 02:38:55
When do you think you will be able to update the library so that these OLEDs would work with Arduino IDE 1.0?
I wanted to use my oled with a big sketch I did in v.1.0 so it would be hell to change it to v.0.23.
Waiting impatiently for an anQuestion by: admin on 2018-12-18 02:38:55
Well I changed the libaries to use them in the 1.0.3 version of the IDE.
In the file SeeedGrayOLED.h change line 27 to #include "Arduino.h" and in SeeedGrayOLED.cpp change in lines 186, 187, 247 and 248 change the "send"-Method to "write"-Method. EaAnswer by: admin on 2018-12-18 02:38:55