Double H driver module uses ST L298N dual full-bridge driver, an integrated monolithic circuit in a 15- lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provided to enable or disable the device independently of the input signals. The emitters of the lower transistors of each bridge are connected together and the corresponding external terminal can be used for the connection of an external sensing resistor. An additional supply input is provided so that the logic works at a lower voltage.
- Light weight, small dimension
- Super driver capacity
- FWD protection
- Heavy load Heat sink
- 2 current probe port
- Power selection switch
- 4 pull up resistor switch
- 2 DC motor/ 4 coil dual phrase stepper motor output
- Motor direction indication LED
- 4 standard mounting hole
MCU controlled vehicle
Driver power supply: +5V~+46V
Driver Io: 2A
Logic power output Vss: +5~+7V (internal supply +5V)
Logic current: 0~36mA
Controlling level: Low -0.3V~1.5V, high: 2.3V~Vss
Enable signal level: Low -0.3V~1.5V, high: 2.3V~Vss
Max power: 25W (Temperature 75 cesus)
Working temperature: -25C~+130C
Driver weight: ~48g
Other extensions: current probe, controlling direction indicator, pull-up resistor switch, logic part power supply.
Datasheet can be download here
|Dimensions||0mm x0mm x0mm|
|L298 Dual H-Bridge Motor Driver||1|
If you pull a 'SENSE' jumper off, it stops current.
Has anyone got an example circuit/code to make use of those pins ? Or maybe for the 'stepping motor' pins ? There is nothing in the docs...Question by: admin on 2018-12-18 02:42:21
Hi there, first you can view the datasheet, this Driver shouldn't use code to control.There is told you in datasheet just use LOW/HIGH voltage.Answer by: admin on 2018-12-18 02:42:21
Can anyone please help me connecting this motor shield to an Ardunino mega?
I don't find any tutorial, and the datasheet is to dificult for my basic knowledge... :-( I want to use it to run the amazing 4wd plataform... :-)
Thanks!Question by: admin on 2018-12-18 02:42:21
Sorry, now I have seen the light, and I have the solution.
ThanksAnswer by: admin on 2018-12-18 02:42:21
I used the Electronic brick - 3 Wire Cable Female to Male to bridge my arduino to it, Good product overall, much cheaper to buy on seeedstudio than elsewhere on the web, plus seedstudios version is sooooo much nicer looking, Easy to use, just read theQuestion by: admin on 2018-12-18 02:42:21
No. This module only gets latitude and longitude. If you need your application to connect to the Cell Network, you could use GPRS BEE.Answer by: admin on 2018-12-18 02:42:21
Question by: admin on 2018-12-18 02:42:21
I am Sorry that we have not done this.
And all the sentences are outputted from the GPS, our reference code only is used to read this information. To complete your idea, I advise you to read GPS datasheet, make sure that whether it can set.Answer by: admin on 2018-12-18 02:42:21
really nice board! in combination with an arduino you have a lot of possibilities of driving dc motors with current regulation or stepper motors with microstepper capability.
For driving a stepper motor or two dc motors you need 4 digital pins and tQuestion by: admin on 2018-12-18 02:42:21
er... are you sure that the gps bee has found enough satellites to locates? i suggest you test the gps bee with u-center first:http://www.seeedstudio.com/wik...Answer by: admin on 2018-12-18 02:42:21
Can't get it to work with a Netduino.
I'm using a power supply that outputs 24V DC 5.0A connected to VMS and GND ad the power Led lights fine.
Settings from Netduino:
EA to 3.3V
Result is that one of thQuestion by: admin on 2018-12-18 02:42:20
Ok, I'll try that. In my setup I gave it 3.3V. I'm a newbie so I'm a little confused when I read the speccifications and they say: "Enable signal level: Low -0.3V~1.5V, high: 2.3V~Vss", so anything above 2.3V would be high, have I misunderstood that?Answer by: admin on 2018-12-18 02:42:20
Well, glad someone has seen the Light, How about Sharing some! Please post your example for the rest of us. I am stuck.Question by: admin on 2018-12-18 02:42:20
Dear customer,Better you can go to forum there is more people can see you problem and help you.Answer by: admin on 2018-12-18 02:42:20
Hi, I want to connect to DC motors with 1.6A stall current each.
Is this driver capable of manage that amount of current or the 2A limit is for the sum of the 2 motors stall current?.Question by: admin on 2018-12-18 02:42:18
Hello, the total DC current is up to 4 A.Answer by: admin on 2018-12-18 02:42:18
I am using this driver with arduino 2WD platform and arduino mega board, and i have noticed that the plaform is not driving in straight line when both motors are spinning the wheels in same direction. The platform is turning slightly left (or right) whQuestion by: admin on 2018-12-18 02:42:18
Two leaves are not exactly same to each other in the world,the same to the motor.So maybe we use the same style of motor,but we can't get the same speed.For your question,you can speed your right motor or slow your left motor,in a word,you can get theAnswer by: admin on 2018-12-18 02:42:19
Question by: admin on 2018-12-18 02:42:14
Sorry , we do not have this example. For this function, you could refer to the datasheet L298 .,Answer by: admin on 2018-12-18 02:42:18