seeedstudio
      Items
      Total
      Go to Checkout
      Your cart is empty
      RFbee V1.1 - Wireless arduino compatible node

      RFbee V1.1 - Wireless arduino compatible node

      SKU 113050002
      $19.50
      6 Available
      $19.50/1pcs+
      $17.55/10pcs+
      $16.57/20pcs+
      $15.60/50pcs+
      ADD TO CART

      Description

      The RFBee is a RF module providing easy and flexible wireless data transmission between devices. It is based on a AVR Atmega168 working as a fully functional Arduino connected via SPI to a TI CC1101 RF transceiver.

       

       

       

       

      Features

      • Range: indoor/Urban: up to 50m; Outdoor line-of-sight: up to 120m;

      • Receiver sensitivity: -95dBm

      • RF data transmission rate: 4,800bps; 76,800bps

      • Working frequency : 868MHz & 915MHz

      • Communication type: Point to Point, or Point to Multipoint.

      • Easy-to-Use serial interface and rich extendable ports

      • Easy-to-Use AT command: Set working mode, Serial Baud Rate, etc.

      • Open source hardware and firmware

      • Socket compatible with the Xbee, so you can plug it into any Xbee socket as a quick replacement.

       

      Note

      only the Rx,Tx, VCC, GND pins are identical to the Xbee. RFbee will not communicate with Xbee, so RFbee need to be used on both ends of the wireless connection.

       

      Documents

      Please visit our wiki page for more info about this product. It will be appreciated if you can help us improve the documents, add more demo code or tutorials. For technical support, please post your questions to our forum.

      Technical Details

      Dimensions60mm x 60mm x 13mm
      WeightG.W 4g    
      BatteryExclude

      Documents

      Reviews

      Questions and Answers

      SUBMIT
      0

      Does this module require the wireless shield as well?

      on Oct 19,2016
      Replyupvote ()
      0

      Hi, ive a kit with 2 nodes... one i would like to use as master and the other as slave, but i dunno how to start! where can i see a tutorial to help me with the basic to start?

      on Oct 19,2016
      Replyupvote ()
      <p>Please refer to its wiki page which includes hardware installation and demo code. Here is the link: <a href="http://www.seeedstudio.com/wiki/index.php?title=RFbee_V1.1_-_Wireless_Arduino_compatible_node" rel="nofollow">http://www.seeedstudio.com/wik...
      on Oct 20,2016 10:48 AM
      Replyupvote ()
      Reply
      0

      Hi, it's possible get the battery status as Seeeduino Stalker?

      on Oct 19,2016
      Replyupvote ()
      <p>yes you can. Normally this problem is depended on your program.</p>
      on Oct 20,2016 10:47 AM
      Replyupvote ()
      Reply
      0

      An Arduino Uno has PWM capability on DIO pins 3,5,6,9,10,11. On the RFBee, only Arduino DIO pins 5,6,9 are available (PD5, PD6, PB1). Pins 5 and 6 work fine, but pin 9 does not seem to function. If I analogWrite(9, 0), it will go low. If I analogWrite(

      on Oct 19,2016
      Replyupvote ()
      <p>Yes, the power_timer1_disable() was staring me in the face and I didn't notice it. I commented it out and then the PWM worked fine. Thanks!</p>
      on Oct 20,2016 10:46 AM
      Replyupvote ()
      Reply
      0

      Is there any RX/TX pins on that module? I mean a pin that a can communicate with an Serial GPS??
      Thanks

      on Oct 19,2016
      Replyupvote ()
      <p>Hi.You can use software serial port to communicate with GPS.</p>
      on Oct 20,2016 10:45 AM
      Replyupvote ()
      Reply
      0

      I have successfully flashed one of my two (2) RFBEES, the first one has worked multipul times(using the reset method), but with the other, i have received multipul AVRDUDE errors (avrdude: stk500_paged_write(): (a) protocol error, expect=0x14, resp=0xf

      on Oct 19,2016
      Replyupvote ()
      <p>Hi.You can download the library(not the new one) on our wiki,may it can solve your problem.</p>
      on Oct 20,2016 10:45 AM
      Replyupvote ()
      Reply
      0

      During the last months playing around with the RFBee I many times wished that there where two pin headers connected with GDO0 and GDO2 pins of the CC1101. Especially in modes that don't use the internal package handling of the CC1101 (synchronous/async

      on Oct 19,2016
      Replyupvote ()
      <p>Okay, thanks for your feedback , we will consider it in the next revision of this module.</p>
      on Oct 20,2016 10:44 AM
      Replyupvote ()
      Reply
      0

      When i tried to compile RFBee firmware with Arduino IDE, it give a lot of errors.. Any information on building the firmare with Arduino?

      on Oct 19,2016
      Replyupvote ()
      <p>got it to work..</p>
      on Oct 20,2016 10:43 AM
      Replyupvote ()
      Reply

        View History

        RFbee V1.1 - Wireless arduino compatible node

        SKU 113050002
        $19.50
        6 Available
        ADD TO CART
        $19.50/1pcs+
        $17.55/10pcs+
        $16.57/20pcs+
        $15.60/50pcs+
        • Best-sellers
        • Description
        • Technical Details
        • Reviews
        • Questions and Answers
        • View History
        Notify me when it's back in stock
        SUBMIT

        Free shipping on your first order over $50 or more. Discounted items included!

        Invalid email address.
        * Discount applys on orders over $50, exclueding shipping fee. Fusion service is excluded from this offer