Blueseeed TH Shield (HM01)
This product was replaced by an updated version Bluetooth Shield V2
- Seeeduino/Arduino compatible
- Up to10m communication distance in house without obstacle
- UART interface (TTL) with programmable baud rate
- A full set of configuration commands
- On board PCB Antenna
- Power supply Voltage: 3.3V
- Baudrate: 9600, 19200, 38400, 57600, 115200, 230400, 460800
- Default Baud rate: 9600, Data bits: 8, Stop bit: 1, Parity: No parity
- Default PINCODE:”1234”
- Bluetooth version: v2.1+EDR
|Dimensions||0mm x0mm x0mm|
Is this bluetooth shield compatible with Uno R3? and Arduino v1.0? Do you have a Arduino board that has a build in bluetooth instead of a shield?Question by: admin on 2018-12-18 02:38:36
Hi,you can jump line to the arduino I/O,it can also work and needn't space.enjoy~Answer by: admin on 2018-12-18 02:38:36
Hi, what is the exact name of the Bluetooth chip? This module is very similar at the Serial/Bluetooth module HC-05. Thank you for reply.Question by: admin on 2018-12-18 02:38:36
Hi,This is a normal phenomenon of Solenoid valve relay.and you can use the dry-Reed Relay,the voltage drops a fewer.with a nice day~Answer by: admin on 2018-12-18 02:38:36
Hi,now we just have this relay which opened normally.
i am connecting an arduino uno to this bluetooth shield ,but every time i disconnect any of them i have to redo the steps from the beginning (remove the device , upload the code then add the device again and pair) .Do i have to do this every time ,is t
In theory, it is possible, but we didn't try it before. Suggest you to get a Motor Driver to control 3-phase motor.
Is the bluetooth shield is compatible with the Amarino toolkit (http://www.amarino-toolkit.net) and a standard Android bluetooth enabled smartphone? Thanks
Hi,Dear.Theoretically this relay can be used hundreds of thousands of times approximatively.And it support a continuously usage.But you might control the frequency of switch.
Hi there,Dimension is 42.00mm*24.00mm*19.50mm
Is there any Arduino code available for test sending and receiving data to the Arduino through the Bluetooth Shield? Also is there any code for Visual Studio that would allow someone to create their own serial monitor other than using the Arduino monit
I downloaded the sscom32e application, but when I try to run it it gives me an error reading ComComboBox1_Comproperty:Registry error (win error code: 2)I am working on a Visual Studio Bluetooth Serial Monitor program, but I am having a hard time findin
yes ,it is because it also communicate via bluetooth protocol.
My bluetooth shield is working fine with the demo programs, but ... How do I disconnect?
Is there a way to go into command mode during communication?
The manual says that pulling up PO0 forces a disconnect, but where is that pin?
Thanks for your feedback, we'll have a further test and upgrade this experience in the next version. Thanks.
You can use the Relay separately without other components .
On the wiki page is written that this shield is not compatible with the HTC Desire (G7) with Android 2.33. Do you know if the HTC Wildfire S (andriod 2.3.5) is compatible with this shield?
The Relay is just a switch, and the two screw ports just like the two sides of a switch. And we can control the switch via the Grove connector. More information you can refer to this wiki: Answer by: admin on 2018-12-18 02:38:35
I have a problem, as this device does not discover on my HTC Desire. It pairs fine with the computer. I followed the "Connecting Bluetooth Shield to Android Phone" guide on wiki, but "SeeedBTSlave" does not show. Any ideas?
This one can't support a current more than 7A if under the voltage of 240VAC.But you can refer to the following link, that one can support a current about 30A :
? the Grove-relay module is in stock now,er, anything that you can order in our shop are in stock, you can order freely.
Dear customer,if the pins is not conflict with others??? that should be OK. So at first you should measure that way.
I've tried unsuccessfully to discover my Arduino with this Bluetooth shield on a Samsung Galaxy Tab 1 and 2. Are there any tricks or know hurdles in getting these to talk to each other? I can discover and pair just fine with a bluetooth dongle I have o
Hi, does your Samsung Galaxy Tab 1 and 2 support bluetooth SPP protocol? this module isn't compatible with bluetooth device without bluetoot SPP protocol.
thx i tried on android V4.03 now its discoverable. but why it doesn't discoverable on Android V2.3?
I just purchased this board locally and have been having trouble getting any Bluetooth Master device to see the Arduino. I'm using a Leonardo board. Is it compatible? Is there a way get a confirmation or status from the Arduino that it as actually conn
That is what I did. But I can not discover it on either my iPhone nor Android phone.
Is there a way get a confirmation or status from the Arduino that it as actually connected to the BT sheild?
I have had my Bluetooth Shield for many months now and still have not been able to get it to work satisfactory. I am trying to read in temperature data off of Analog pin 1 of my Arduino UNO microcontroller. I modified a program that I found on the web
Sorry , i do not got it clearly , can you email to me :firstname.lastname@example.org
And please give me more info , such as what arduino you are using , and how you connect this shiled with other part like your temperature sensor . Thx
I built an electric auto. See it at WWW.EVALBUM.COM/3584. In front is the Arduino mega 2560 which gathers all dashboard data and controls peripherals. It runs all the time, even during charge, reporting on charging battery conditions. The dashboard is
I'm using the hardware Rx and Tx, pins 0 and 1. I am getting both xmit and rcv clearly. My problem is restablishing connection. The Bee has a PIO(11) pin that I can set to use +AT commands. Is this pin available on the shield so I can use those command
I downloaded the sscom32e application, as Jacket Chueng suggested, but when I try to run it it gives me an error reading ComComboBox1_Comproperty:Registry error (win error code: 2)I am trying to work on a Visual Studio Bluetooth Serial Monitor program.
I will try it on another PC I am running Windows 7 and that may be the issue. Is this monitor an open source, with code available?
I have been trying to get the bluetooth shield to run at 115200 baud and cannot get it to work. I am using hardware serial ports to communicate with the shield and program the Uno using the AVR in system programmer. I have gotten it to work at 38400 ba
Hey,when using SoftwareSerial, do not set the baud rate above 38400.
Is Hands Free Protocol available for this device? I see "SPP Firmware installed" above, is the HFP firmware written for it?
Hey,it just has a SPP firmware installed,but no HFP.
Hi Gloria.We just could connect one slave device to a Master device now.
I use a Arduino Mega, throw the Serial3 (And It works).
I need to increase the baud rate (_ 38600). I tried to send the right command, but nothing change...
What should I do ?
How to proceed ?
Hi.If you use Mega with bluetooth,you may modify your code:#define RxD 11;
#define TxD 12.And connect digital 6(7) to digital 11(12) via jumper wire.
I can't figure out how to disconnect or pair the device. Is there any FIX, I tried everything, nothing works, just green light blinking twice.
Hi,Harnoor.If your BT can't access pairing station,maybe there are something wrong with your program.Could you tell me how did you set your BT?If you use Arduino/Seeeduino,just upload the code and turn the switch to NC.
I have the same issue as the guy below me. I have an UNO R3. I have double checked my pins and code but I cannot get it to get into "pairing mode"(red/green blink). I only get green blink in the format - -, pause, - -, and so forth every second or so.
Hi David.you can have a try as the following method,it is very simple.
I have the shield and arduino uno r3, but cannot get the arduino to send commands to the BT shield. I cannot get the BT shield into pairing mode red/green lights. When I send commands through USB via SSCOM3.2 or PUTTY I get garbage text in return and t
Hi you need not any commands,please download Bluetooth Shield Library for Arduino 1.0,and then modify some codes as the wiki said,soon you can have a pair with others.
I tried to use your example with an Arduino UNO and the Bluetooth shield, and everythings work fine! Now I cannot use the Software serial because is used by a GSM shield so to communicate with your Bluetooth module, I need to use the othe
Hi, this module can't communicate with main board via I2C port.
Yes you can, but please pay attention to the occupied pins. More information you can refer to the wiki of schematic.
I am working on a project and I have connected the Bluetooth shield with a https://www.sparkfun.com/produ.... What battery characteristics would be the most appropriate to the system?
I'm sorry we don't have a 5-9v battery in this small size.
i'm not an expert, i meant a table like this:http://www.seeedstudio.com/wik...
I have uploaded every single "Slave" code sample from the github mentioned on the bluetooth shield wiki. None of them work. Where can I find WORKING example code for this shield on an arduino uno R3?
were are the librairies on the wiki? I can't find any library on the github as well.
Please I've encountered several problems with this card for an entire week.
Finally I have succeed makin' the LEDs green and red blinkin'.
But when I use the command:
which is supposed to connect me
i agree with you but this sensor is also a bluetooth module so it should be inquirable buy my bT Shield but is not
What are your suggestion plz?
i can connect my android with bluetooth shield But i want to know how do i control my RC tank .HELP ME WITH A CODE
Hey,i'm sorry we don't have resource to design any custom application,but you can search some resource from the wiki or the forum.Thanks for you comprehension.
Hoping by re-posting at the top alerts are sent: My shield doesn't look like the one in the pictures; the board is bigger and squarer. It's labeled "Bluetooth Shield v2.0 06/12/2014". I am using the sample code for "Slave_Recv.ino" from the Github site
I got reply from Seeedstudio. It's v 2.0 and it's wiki page is here: http://www.seeedstudio.com/wik... I was able to set the name and PIN using the code from the example
I've paired the Bluetooth Shield with an Arduino Uno and have not been able to check the status (using PIO1) and disconnect (using PIO0) if the status set to connected. Do you have an example sketch?
If anyone has any help it would be appreciated. I would like to be able to send a user command (using the template provided at http://www.seeedstudio.com/for... that c