
Note:
Enjoy 5% off when you purchase any one MeshCore device – the SenseCAP Solar Node P1-Pro (SKU 100023690) or the Wio Tracker L1 Pro (SKU 100030144).
Get up to 8% off when you add both models to your cart.
No quantity limits – discount auto-applies at checkout.
MeshCore is a multi platform system for enabling secure text based communications utilising LoRa radio hardware. It can be used for Off-Grid Communication, Emergency Response & Disaster Recovery, Outdoor Activities, Tactical Security including law enforcement, private security and also loT sensor networks.
SenseCAP Solar Node P1-Pro for Meshcore comes with pre-flashed Meshcore Repeater firmware.
Note:
To replace the battery, please use a button-top 18650 battery. Please check this [compatible battery example] for reference.
Note:
Enjoy 5% off when you purchase any one MeshCore device – the SenseCAP Solar Node P1-Pro (SKU 100023690) or the Wio Tracker L1 Pro (SKU 100030144).
Get up to 8% off when you add both models to your cart.
No quantity limits – discount auto-applies at checkout.
Main controller | Xiao nRF52840 Plus (Nordic nRF52840, ARM® Cortex®-M4 32-bit processor with FPU, 64 MHz, 256KB RAM, 1MB Flash, 2MB onboard Flash) |
LoRa Module | Wio-SX1262 (Semtch SX1262, TXOP=22dBm@862-930MHz) |
GPS Module | L76K (Support GPS/GLONASS/Galileo) |
Antenna | LoRa: Type: Rod-shaped rubber antenna Frequency range: 868-915MHZ Gain: 2dbi |
GNSS: GPS L1 C/A: 1575.42MHz GLONASS L1: 1602MHz BeiDou B1: 1561.098MHz | |
Bluetooth 5.0 | |
Solar Panel | 5W |
Interface | Grove *1: IIC/GPIO/UART |
USB-C debugging | |
Button | Power on/off |
Reset | |
User-defined | |
LED | Charging status indicator lights *2 |
Solar panel status indicator light *1 | |
Mesh heartbeat light *1 | |
User-defined *1 | |
Power supply | Type-C: 5V 1A |
| Solar power supply: 5V 1A |
Battery | 4 x 18650 lithium batteries (3350mAh each) ● Supporting Type-C and solar charging. ● Discharge environment:-40 ~ 60°C ● Charging environment: 0 ~ 50°C |
Certification | FCC、CE |
Dimension | 191.2 x 201.2 x 42.1 mm |
① | 2dbi, 868~915MHz rubber rod antenna | |
② | Universal joint bracket, angle adjustable. | |
③ | Bracket connector, can support the antenna | |
④ | RF Cable; RP-SMA Male to RF-SMA Female; 300mm | |
⑤ | Hoop bracket | Diameter: 70-100mm |
⑥ | Hoop ring | |
⑦ | Power switch |
⑧ | Reset |
⑨ | User-defined |
⑩ | Red light on: Charging |
⑪ | Green light on: Charged |
⑫ | Yellow light on: Device is exposed to light. |
⑬ | Blue light: Wait to be defined |
⑭ | White light: Mesh light |
⑮ | Type-C: 5V 1A |
SenseCAP Solar Node P1-Pro (with GPS & battery) | x1 |
Mounting Brackets ● Universal Joint ● Connector ● Hoop Bracket ● Hoop Ring | x1 |
2dBi 868 - 915MHz Rubber Rod Antenna | x1 |
RRF Cable; RG316 coaxial cable; RP-SMA Male to RF-SMA Female; 300mm | x1 |
1/4-20 UNC Hex Head Machine Screw, 6 mm Long(Screw Pack) | x2 |
Screw, Phillips Pan Head Machine, M6 × 14 mm, P1.0(Screw Pack) | x4 |
Black Type-C Cable | x1 |
User Manual | x1 |
This device is pre-flashed with MeshCore repeater firmware. Powered by the Seeed XIAO nRF52840 Plus Module, Wio-SX1262 LoRa module, and L76K GPS modules, this solar-driven node leverages the nRF52 architecture for ultra-low power management—delivering long-range communication and precision positioning while maintaining full compatibility with the MeshCore ecosystem for decentralized, off-grid networking and mobile app integration.